Home / Professional Products / Mixers / Digital SmartMixer - ATDM-1012

Digital SmartMixer

ATDM-1012

Acoustic Echo Canceller and Web Interface


  • Equipped with 22 Inputs × 12 Buses full matrix mixer, including 8 Sub Iinpts systems
  • 10 MIC/LINE inputs with high-quality microphone preamplifier and stereo amplifier (CH 7/8, 9/10 can be used as Stereo Link)
  • Up to two sets of hanging array microphone ES954 (sold separately) can be connected to the microphone inputs
  • 8 Balanced outputs with BTL circuit
  • 2 Unbalanced stereo outputs and Microphone level output
  • USB audio input/output (1 stereo input, 1 stereo output)
  • Independent 4 Groups of SmartMixer with optional gain sharing or gating mode
  • Equipped with echo canceller (up to 10 Microphone inputs) and noise canceller which can be used at the same time
  • Each input system is equipped with a 4-band equalizer (sub-input only low-cut) and each output system is a 12-band equalizer
  • Equipped with 10 Compressors/DeEsser and 8 frequency band Feedback Suppressors which can be inserted into each input/output system
  • 2 Unbalanced stereo inputs with Ducker function
  • Each output system has a Limiter
  • Equipped with a convenient Oscillator function, you can check the audio of each output system
  • Audio input/output settings can be made from the front panel and detailed settings can be made from PC by Web Remote
  • Offline device settings can be done through the Web Remote Manager application
  • Can be controlled from the outside through the IP remote protocol










    • audio technica ATDM-1012

    • ATDM-1012 Audio Specifications

    Frequency Response

    20 ~ 20,000 Hz (MIC -16 dBu) : +1.0/-1.0 dB
    20 ~ 20,000 Hz (MIC -60 dBu) : +1.0/-2.0 dB
    20 ~ 20,000 Hz (LINE 24 dBu) : +1.0/-1.0 dB
    20 ~ 20,000 Hz (LINE -40 dBu) : +1.0/-2.0 dB
    Dynamic Range (Typical)

    112 dB or higher, A-weighted/ST
    Signal-To-Noise Ratio

    92 dB or higher, A-weighted/ST
    Headroom

    20 dB or higher
    Equivalent Input Noise

    -127 dBu or less, Rs = 150 ohm, DIN
    Common-mode Rejection Ratio

    80 dB or high, 1 kHz
    Noise

    -88 dBu or less, A-weighted
    Maximum Gain

    64 dB
    Channel Separation

    -80 dB or less, 1 kHz unity
    Total Harmonic Distortion

    0.03% or less, 1 kHz unity
    Audio Input

    MIC max.: 0 dBu
    MIC unity: -40 dBu
    LINE max.: +24 dBu
    LINE unity: +4 dBu/0 dBV/-10 dBV/-20 dBV
    ST max.: +20 dBV
    ST unity: -10 dBV/-20 dBV
    Audio Output

    OUTPUT 1~8 max.: +24 dBu/+20 dBV/+10 dBV
    OUTPUT 1~8 unity: +4 dBu/0 dBV/-10 dBV
    OUTPUT ST max.: +20 dBV/+10 dBV/-13 dBV
    OUTPUT ST unity: 0 dBV/-10 dBV/-33 dBV

    ATDM-1012 Other Specifications

    Phantom Power

    +48V DC
    Input Attenuation

    -24 dB
    Input Connections

    MIC/LINE INPUT 1 ~ 10 Euroblock connectors (3-pin)
    ST INPUT 1/2 Euroblock connectors (3-pin)
    Output Connector

    OUTPUT 1~8 Euroblock connectors (3-pin)
    ST OUTPUT 1/2 Euroblock connectors (3-pin)
    Controls

    IP protocol: RJ-45 × 1 pc
    IP address: 192.168.33.102 (default)
    Communication speed: 100 Mbps
    Link Connector

    IP protocol: RJ-45 × 2 pc
    Communication speed: 100 Mbps
    USB Connect

    Channel: Stereo input x 1 ch, stereo output x 1 ch (24-bit)
    Communication speed: High-speed (480 Mbps)
    AD/DA

    Resolution: 24-bit
    Dynamic range: 115 dB
    Accessories Furnished

    Euroblock connector x 22, Power cable

    ATDM-1012 General Specifications

    Power Supply

    100 ~ 240 V AC (50/60 Hz)
    Rating Capacity

    65 W
    Operating Temperature Range

    0 ~ 40° C
    Operating Humidity Range

    25 ~ 85% (No frost)
    Dimensions

    482.6 mm × 44 mm × 324.3 mm (W×H×D)
    Weight

    3.6 kg

    ATDM-1012 Input/Output Specifications

    Input Connections

    BAL 1 ~ 8 -
    Load impedance : 150Ω;
    Input level - TYP : +4 dBu/-10 dBV/0 dBV;
    Input level - MAX : +24 dBu;
    Connector : Euroblock (BAL)

    UNBAL 1/2 (L/R) -
    Load impedance: 150Ω;
    Input level - TYP : 0 dBV/-10 dBV/-33 dBV;
    Input level - MAX : +20 dBu;
    Connector : Euroblock (UNBAL)
    Output Connector

    BAL 1 ~ 8 -
    Load impedance : 150Ω;
    Input level - TYP : +4 dBu/-10 dBV/0 dBV;
    Input level - MAX : +24 dBu;
    Connector : Euroblock (BAL)

    UNBAL 1/2 (L/R) -
    Load impedance: 150Ω;
    Input level - TYP : 0 dBV/-10 dBV/-33 dBV;
    Input level - MAX : +20 dBu;
    Connector : Euroblock (UNBAL)

    Download

    audio technica support Locate_V1.0.3.zip - Locate Apps for Windows and OSX
    audio technica support ATDM-1012_QSG.pdf - ATDM-1012 Quick Start Guide
    • Social